Loughborough University
Browse

File(s) under embargo

Reason: Publisher requirement.

6

month(s)

30

day(s)

until file(s) become available

Method of computational design for additive manufacturing of hip endoprosthesis based on basic‐cell concept

journal contribution
posted on 2024-02-01, 15:01 authored by Pavel Bolshakov, Alex G Kuchumov, Nikita Kharin, Kirill Akifyev, Evgeny Statsenko, Vadim SilberschmidtVadim Silberschmidt

Endoprosthetic hip replacement is the conventional way to treat osteoarthritis or a fracture of a dysfunctional joint. Different manufacturing methods are employed to create reliable patient‐specific devices with long‐term performance and biocompatibility. Recently, additive manufacturing has become a promising technique for the fabrication of medical devices, because it allows to produce complex samples with various structures of pores. Moreover, the limitations of traditional fabrication methods can be avoided. It is known that a well‐designed porous structure provides a better proliferation of cells, leading to improved bone remodeling. Additionally, porosity can be used to adjust the mechanical properties of designed structures. This makes the design and choice of the structure's basic cell a crucial task. This study focuses on a novel computational method, based on the basic‐cell concept to design a hip endoprosthesis with an unregularly complex structure. A cube with spheroid pores was utilized as a basic cell, with each cell having its own porosity and mechanical properties. A novelty of the suggested method is in its combination of the topology optimization method and the structural design algorithm. Bending and compression cases were analyzed for a cylinder structure and two hip implants. The ability of basic‐cell geometry to influence the structure's stress–strain state was shown. The relative change in the volume of the original structure and the designed cylinder structure was 6.8%. Computational assessments of a stress–strain state using the proposed method and direct modeling were carried out. The volumes of the two types of implants decreased by 9% and 11%, respectively. The maximum von Mises stress was 600 MPa in the initial design. After the algorithm application, it increased to 630 MPa for the first type of implant, while it is not changing in the second type of implant. At the same time, the load‐bearing capacity of the hip endoprostheses was retained. The internal structure of the optimized implants was significantly different from the traditional designs, but better structural integrity is likely to be achieved with less material. Additionally, this method leads to time reduction both for the initial design and its variations. Moreover, it enables to produce medical implants with specific functional structures with an additive manufacturing method avoiding the constraints of traditional technologies.

Funding

Mega-grants program hosted by Perm National Research Polytechnic University. Grant Number: 075-15-2021-578

History

School

  • Mechanical, Electrical and Manufacturing Engineering

Published in

International Journal for Numerical Methods in Biomedical Engineering

Volume

40

Issue

3

Publisher

Wiley

Version

  • AM (Accepted Manuscript)

Rights holder

© John Wiley & Sons Ltd

Publisher statement

This is the peer reviewed version of the following article: Bolshakov P, Kuchumov AG, Kharin N, Akifyev K, Statsenko E, Silberschmidt VV. Method of computational design for additive manufacturing of hip endoprosthesis based on basic-cell concept. Int J Numer Meth Biomed Engng. 2024; 40(3):e3802. doi:10.1002/cnm.3802, which has been published in final form at https://doi.org/10.1002/cnm.3802. This article may be used for non-commercial purposes in accordance with Wiley Terms and Conditions for Use of Self-Archived Versions. This article may not be enhanced, enriched or otherwise transformed into a derivative work, without express permission from Wiley or by statutory rights under applicable legislation. Copyright notices must not be removed, obscured or modified. The article must be linked to Wiley’s version of record on Wiley Online Library and any embedding, framing or otherwise making available the article or pages thereof by third parties from platforms, services and websites other than Wiley Online Library must be prohibited.

Acceptance date

2024-01-07

Publication date

2024-01-21

Copyright date

2024

ISSN

2040-7939

eISSN

2040-7947

Language

  • en

Depositor

Prof Vadim Silberschmidt. Deposit date: 31 January 2024

Article number

e3802

Usage metrics

    Loughborough Publications

    Exports

    RefWorks
    BibTeX
    Ref. manager
    Endnote
    DataCite
    NLM
    DC